Recent content by MellonRover
-
Before I buy 18” wheels….
You anywhere near Wichita TX? I bought the SYA from him. https://www.facebook.com/share/p/16Yfzxkjif/- MellonRover
- Post #8
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
Like this? I ordered these, just concerned about cutting clean/straight. I'm going to install amp and just tape the wire so it's insulated and let sleeping dogs lie. If needed I have the connectors though...- MellonRover
- Post #10
- Forum: LR4
-
Before I buy 18” wheels….
Narrow tires ( pizza cutters) work wonders for rubbing. Also pay attention to offset. Too close in and it will rub on control arm, too far out and you'll lose a fender flare, and it stresses bearings even more. Front bearings don't need any help...the 275 on your example is more of an issue than...- MellonRover
- Post #2
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
Time consuming, but very easy to get to the rear modules. Replacement amp is on its way as we speak. At least I can vacuum all the crap under the front seat real good!- MellonRover
- Post #7
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
Welp....359 degrees later, I'm just about where I thought I'd have the problem. Prior to dealing with fiber optic " Christmas lights type" one unit fails the others fail too. Yep, all rear modules checked, bypass the under seat amp ( what I initially thought) and blinking whet to solid red...- MellonRover
- Post #5
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
This is what I'm going to do next.- MellonRover
- Post #4
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
Already on it Went to u pull yesterday and got the harness from radio to rear window area from an lr4 ( tore that thing apart, and dread having to do that on mine) made long jumper and short test lead. I get light after the chew spot, and the loop did nothing. So either something downstream of...- MellonRover
- Post #3
- Forum: LR4
-
Break in the MOST ring? Fiber optic interconnect
Anyone have experience repairing/splicing the most fiber connection? Center dash screen stuck on LR logo, no controls of audio/nav or backup camera. Thinking of using the brass splices you can buy online. Here is the terrible pic of the wire. Can see red light when truck wakes up. So that can't...- MellonRover
- Thread
- Replies: 9
- Forum: LR4
-
Everything about tires for LR4/ LR3 with 18" wheels
Tuffant USA is phasing steelies out. If you are going to do it, you should pull the trigger. Defender "steelies" also are a direct fit. Some say their dealer was overstocked with takeoffs and sold them cheap.- MellonRover
- Post #1,022
- Forum: LR4
-
Front propshaft / driveshaft replacement
Thanks m32! Your video was very helpful. Just did front and rear propshafts.- MellonRover
- Post #10
- Forum: LR4
-
Front driveshaft bolts went missing!! And an introduction
So....update. Front driveshaft started clacking. Must have gotten junk in there. I packed as much grease in and buttoned up in situ. But that must not have been enough. What an annoyance that was to replace. Did rear too because...why not. ($105 in just bolts...)- MellonRover
- Post #11
- Forum: LR4
-
Any tips for SYA kit strap routing
Mine don't rub. Here's the best I could do for pics. My straps have a permanent "shape" to them now, if I recall there was a twist to add some tension and make them shape that way- MellonRover
- Post #2
- Forum: LR4
-
AirDownGearUp SS1: Drawer, Kitchen, Storage and Sleeping Platform Systems for Land Rover LR4
Very nice. What are weight capacities of the kitchen sections, seeing as there are no legs.- MellonRover
- Post #3
- Forum: LR4
-
-
Everything about tires for LR4/ LR3 with 18" wheels
265 70 18 with SYA kit. Skinny and more sidewall. 32.6" tire- MellonRover
- Post #988
- Forum: LR4
