Search results
-
Coolant Leak - Easy Fix - Check Yours!
I learn a lot ahead of time by these posts. Thanks. -
Help Please
Ouch! My local Land Rover dealership is 6 miles from my house so I took my chances on driving there this morning without a thermostat. I added water in hopes that it would keep the engine cool for the 10 minute drive. I literally made it to the entrance of the dealership before seeing a smokey... -
Help Please
It's part of owning a LR I suppose. I really don't want to order a whole new housing, I just need to part that unscrews with the T25 hex screws. The t-stat has two medal sides that slide into place within the plastic on the housing. I guess the plastic had become weak and essentially broke. -
Help Please
Found the problem. The thermostat was fine, but noticed the little grooves the t-stat slides into inside of the housing, one of the plastic grooves completely broke off of the housing. I guess I'll have to order a new housing. Joy. -
Help Please
Yes it was opening normally before this. I'm using Dex-Cool 50/50. I'm not sure why this is happening. I'm about to open the t-stat housing as we speak and make sure the t-stat isn't bad. -
Help Please
I added the antifreeze to the "Cold Fill Range" and drove it down the road and noticed the engine temp gauge was at red. I pulled back into the garage and the antifreeze tank was filled to the brim. What is causing this and should I just drain the coolant out and fill it back up, but with LESS... -
Anti-Freeze
HELP PLEASE: I added the antifreeze to the "Cold Fill Range" and drove it down the road and noticed the engine temp gauge was at red. I pulled back into the garage and the antifreeze tank was filled to the brim. What is causing this and should I just drain the coolant out and fill it back up... -
Anti-Freeze
I recently changed my t-stat and lost more than enough coolant from detaching hose in the process. I poured the remaining coolant back into the anti-freeze tank and now I'm a bit low from the coolant I lost. I am the second owner of the truck and haven't done any coolant flushes so I'm not sure... -
RPM Needle Fluxuating
From what I have gathered from other online sources is that it could be anything from water in the fuel, a broken part in the throttle body, a dirty mass airflow sensor, or a dirty air filter. I also read that the other LR3 owners had taken to the shop after experiencing this, but that the... -
RPM Needle Fluxuating
Started my truck last night and headed down the road. I got about a mile from home and noticed my RPM's rising and dropping rapidly from 1k-2k. I'm not sure what the cause is? As the motor warmed up it didn't occur as often or as vast as 1000-2000rpms. The needle would fluxuate at idle as well... -
New 2012 HSE owner!
Congrats. I've got an LR3, but I drule over the the LR4. -
Looking at an 06 LR3, help needed
I've got an '05 with 84,600 miles on it. I am the second owner. Although I have only put about 8k miles on it I have had no major issues. I have only changed out the t-stat. -
Drilling Tips
Silly me, at first I had not used cutting oil and right away I could see my $30 HSS bit being chewed away by the steel. Luckily I didn't go too long without the oil. I'll keep these measurements in mind next time I go for a rear shackle. Thanks. -
Drilling Tips
Thanks. I had to use a 7/8" bit and cutting oil to bore the hole out. The pin still did not fit so I sanded it down. -
Good Story. Thanks Johnson Rods.
I was going out with a few friends last night. As I pulled to a stop light I was rear ended. Slightly. The girl was in a small SUV with her little brother. She was 16 years old. No one was hurt, thankfully. Because it was dark out I could not see the damage clearly so this morning I looked and... -
Drilling Tips
I purchased two 3/4" D-ring shackles for my front bumper. The holes in the bumper for the shackles measure 3/4", but the shackle pin is slightly larger therefore the pin will not slide through the hole. I'm kind of nervous about drilling through the powder coated bumper, but I will do it. I got... -
Train Horn
I'll post a video and detailed pictures when I get the parts in. Should be fun! -
Train Horn
Ordering a HornBlasters train horn for my LR3. Should be good! :biggrin: -
2006 LR3 horn is not working
Check the wiring on the horn itself. It may of come loose from the connection. -
Do you rotate your tires?
I haven't done a rotation yet on my Kelly Safari TSR's, but I'm due for one sooner than later. I'll probably do B mainly because of the tire wear pattern. -
Rear glass gas struts - anything special?
British Parts Utah has them on their website for $23+shipping. Part # BHE780012 -
Transmission replacement
You don't have to pay their price. I know of someone who ordered a rebuild from RoverLandParts and he hasn't had any issues with it. http://www.roverlandparts.com/LR3-transmissions-complete.aspx
