Search results
-
F
How-To DIY: Replacing LR4 fuel system low pressure sensor
isn't 12.26 low for resting voltage? Full charge should be 12.6, or was that a typo? -
F
heated windshield on -> voltage drops to 12.7
I thought the windshield had two heating elements, one on each side, and each has a 30A fuse. The mirrors draw about 2A each. The blower fans can draw a good bit too. I guess you could pull those fuses and see what the load is without (in case other things got turned on like the rear... -
F
2011 LR4 HSE Coolant Leak Help
I thought the correct coolant for our vehicles was yellow/orange, not pink? -
F
Three amigos after getting to operating temp.
Aren't HDC and special programs ABS related? I thought lowering would happen due to suspension faults. -
F
When is it time to say goodbye?
When we got ours in 2017, the heated mirrors didn't work. I mentioned it to the various shops that serviced it for years who all told me they were fine and only activated when the control unit determined it should. I eventually got my own GAP tool and lo and behold, there were codes for the... -
F
4WD System Question
There's an electric motor that activates the clutchpack in the locking diff. The ABS-based traction control is very good though, definitely doesn't behave like an open diff vehicle. -
F
Front air suspension
If you're on your original compressor, the desiccant likely turned to dust and some of it is preventing the solenoid from closing all the way. You'll want to replace the desiccant (or whole compressor unit), and clean the valves blocks out. -
F
2015 LR4 - Major engine work - Sell / Sell Parts
I think if you're not mechanically inclined and have time to do the work, these can be very expensive to keep running. Parting it out means it takes up space for a while in a state of decay. If your wife really likes the platform, you could look at picking up a new-to-you one for less maybe... -
F
Everything about tires for LR4/ LR3 with 18" wheels
Mine read higher than actual before I got new tires, and with the 255/60r19 now reads pretty much spot on. It does read a tad bit low above 70 (about 1mph or so) but I haven't bothered to fix that yet. What are the increments for the MSB setting? -
F
Project Dark Knight Rising
For whatever it's worth, I'm rooting for you on this. -
F
Everything about tires for LR4/ LR3 with 18" wheels
Did you mean staying with XL? -
F
Compomotive wheels bent?
The 2x4 is used to lower the car onto and trick the system intro raising you further? -
F
what happened to the show-off sticky thread?
@Griffin @joey , any idea what happened here? -
F
what happened to the show-off sticky thread?
Where did the sticky thread go where we could post pictures of our rigs on the adventures we take? -
F
Tire sizes
I believe the door card on my 2012 lists 19" wheels, but the same PSI as what you have listed above (37/43). -
F
bad lower ball joint lead to howling?
I went the whole new arm route myself and would do that again. -
F
bad lower ball joint lead to howling?
I replace the whole arms, not just the ball joint. You have to get the angle just right to get the arm in there to clear the axle. I could not get the ball joint to release from the knuckle without the separator tool. Not my crappy pickle fork, nor whacking the knuckle with a mallet. -
F
2012 LR4 - Diagnosing two separate vibrations
I'd check for play in the u-joint and center driveshaft bearing. The failure symptoms described here sound a bit like what you're experiencing: https://www.fcpeuro.com/products/rover-center-support-eurospare-tvb500390brg -
F
Gas smell after driving. No error codes. No visible leaks.
Or the vacuum pump -
F
maintenance history since new 2013
Was it pinched during install or junk from the factory? Are you replacing just the oring or the whole crossover? -
F
maintenance history since new 2013
So it leaked again? Bad o-ring or did the plastic seam fail?
