Search results
-
F
gallery pressure
I logged the change to off-road height with the new compressor. For reference here's the old: And with the new compressor: Doesn't look all that different. -
F
gallery pressure
I installed the new compressor on Sunday and logged the reservoir being filled again. I also have a log of the old compressor doing the same, though I didn't log the full fill of the reservoir, only up to the first thermal cutoff. Old: New: I haven't had a chance to log a normal to... -
F
Rear Wiper
it only does this if you have the front wipers on (even in rain sense). It is useful. My same vintage VWs do the same. -
F
gallery pressure
If you view the graph in the IID tool (rather than numeric data) you'll have a chance to see the data trends (including elapsed time). But if it's less than a minute, it sounds like my compressor might indeed be tired. -
F
bad lower ball joint lead to howling?
Also, the second side went *much* faster as I didn't have to pause to go watch videos for how to hammer the hub out of the knuckle. I printed out the relevant pages from the workshop manual and just followed along. -
F
gallery pressure
Any idea how quickly you got back to 250psi after the height change? -
F
gallery pressure
I failed to capture the startup sequence, you have to turn the ignition on, start the live capture, and then crank the engine... I did get the height change, but the system properly pressurized. So the height change took 5-10 seconds, then about two minutes to reach 1720 kPa (250psi) again. -
F
gallery pressure
I ordered a new Hitachi for $480 delivered, should be here Monday. I was logging gallery pressures yesterday and tried searching for that term but came up largely empty handed. I figured leaving some data that comes up in searches might help someone in the future. Strangely I did not get many... -
F
2016 LR4 Suspension Issue
Found a supposedly genuine Hitachi on Amazon for $480. I will inspect it carefully before installing it to make sure it is genuine. If no Hitachi markings, I'll send it back. -
F
gallery pressure
I was hoping to get some data points from the community regarding gallery pressure changes over time. Specifically, I'd like the following data from folks that have an IID Tool and are inclined to document behavior: 1. From cold start, starting gallery pressure, ending gallery pressure and... -
F
2016 LR4 Suspension Issue
The center valve block actually just controls the flow to/from the reservoir. The gallery connects to the compressor and front/rear valve blocks and has a pressure sensor. The front and rear blocks have 3 valves - individual valves for each side, and a cross link valve. To inflate, if there's... -
F
bad lower ball joint lead to howling?
The two hubs were a $505 from Lucky8. I got extra axle nuts ($18), but it turns out the hubs come with, so that wasn't necessary. I had asked them and they said they didn't. No biggie. Things came apart easily, thankfully there are videos for how to knocking the hub out, as there's not a lot... -
F
2016 LR4 Suspension Issue
I had repressurized the system and gone for a test drive of my new hubs. This was raising from normal to off-road upon return, the back went up quickly (a handful of seconds), the front was measured in minutes. -
F
bad lower ball joint lead to howling?
I tried two indy shops that specialize in land rover. First time they sent me home because the lock but on the tie rod was frozen. Replaced both tie rods and went back, came back with the wheel off center. Took it back again and this time it came back even more crooked. Took it to another... -
F
2016 LR4 Suspension Issue
Yes, I'm suspecting the center valve block, if it can't store air in the tank then the compressor would be doing all the work. -
F
bad lower ball joint lead to howling?
Got the new Timken hubs installed and I'm happy to report that the noise is gone. There's still a clunk in the steering somewhere, but that's a problem for another day. -
F
2016 LR4 Suspension Issue
Happy to report the front didn't sag overnight, I'll put the splash shield back on tonight. -
F
2016 LR4 Suspension Issue
So far just the front, but given how slowly it went up to off-road height I suspect something else is up. -
F
2016 LR4 Suspension Issue
I stuck with the original tiny o-ring but used the rest of the new kit, all with a touch of plumbing grease when assembling. I'm not sure my leak was from the valve block, but the front was sagging quite quickly. I had the thing on jack stands for front hub replacement and got stuck due to... -
F
2016 LR4 Suspension Issue
Ok, the smaller one is too thin: The rest seem good though. -
F
2016 LR4 Suspension Issue
My kit from British parts of Utah came in today, and I'm pleased to report that the kit looks spot on: Top is the old, bottom is the new. -
F
Ironman 4x4 Drawers
I believe the Front Runner drawers have a provision for an extension to reach the spare tire winch. I wonder if the winch could be relocated (say to the bumper area) with just a pulley in the original location and a longer cable, and remove the need to access it through the interior. -
F
Be honest! What's the deepest snow you've driven in with your LR4
It looks sharp, does pretty much anything you ask of it, the only downside is the fuel consumption. We have multiple cars already, so for us the LR4 is there for fun/family trips/inclement weather. If we had to drop to one car only, the LR4 would probably be the one that stays. That could... -
F
2016 LR4 Suspension Issue
The kit I got from amazon had clearly different sized O-Rings from what was fitted. Would they have worked? Perhaps, but they were far enough off that I just returned them.
